Microtrol Co.

logo-microtrol

SYSTEM COMPONENTS

Public Address & General Alarm Systems (PAGA)

SYSTEM COMPONENTS

PMOD 1 XCO 001

X-Controller Module

Features and Functions

  • Controller for Intercom, PA/GA and PA solutions with up to 400 terminal devices
  • Networking of up to 250 X-Controllers
  • Control of warning sequences
  • 4 Gigabit Ethernet interfaces for flexible network connection
  • 12 bidirectional potential-free control inputs and outputs
  • Power supply of the internal electronics via PoE (with redundancy) or separate DC supply
  • Integrated self-monitoring
  • Configuration via INDUSTRONIC management tools

PMOD 8 XDG 001

Digital Gateway Module

Features and Functions

  • Connection of up to 8 digital INDUSTRONIC terminal devices via 2-wire technology
  • 2 Ethernet interfaces for redundant network connection
  • Redundant connection of terminal devices to 2 different XDG modules possible
  • Integrated self-monitoring
  • Permanent automatic monitoring of all connected terminal devices, connection cables, and power supplies
  • Configuration via INTRON-X management tools

PMOD 24 XIO 001

I/O Module

Features and Functions

  • 24 bidirectional potential-free control inputs and outputs
  • 2 Ethernet interfaces for redundant network connection
  • Power supply of the internal electronics via PoE (with redundancy) or separate DC supply
  • Integrated self-monitoring
  • Configuration via INDUSTRONIC management tools

PMOD 6 XAL 001

Analog Line Module

Features and Functions

  • 6 analog audio interfaces with
  • 2 x 4-wire audio (full duplex)
  • 4 x 2-wire audio (half duplex)
  • 24 bidirectional potential-free control inputs and outputs
  • 2 Ethernet interfaces for redundant network connection
  • Power supply of the internal electronics via PoE (with redundancy) or separate DC supply
  • Integrated self-monitoring
  • Configuration via INDUSTRONIC management tools

PMOD 4 XBC 001

Beacon Control Module

Features and Functions

  • Control of up to 4 AC or DC flashing warning beacon circuits
  • Flashing warning beacons can be wired as line or loop
    • Xenon, LED, etc.
    • 115 / 230 V AC
    • 24 / 48 / 60 V DC
  • Continuous automatic line monitoring of the flashing warning beacons for cable break, short circuit and ground leakage (option)
  • 2 Ethernet interfaces for redundant network connection
  • Power supply of the internal electronics via PoE (with redundancy) or separate DC supply
  • Integrated self-monitoring
  • Configuration via INDUSTRONIC management tools

Exchange Control Board

1 DXC 04

Features and Functions

  • Connection of up to 192 digital or analog intercom stations
  • Addressing of up to 65,000 stations, speaker circuits, etc.
  • Switching of up to 120 simultaneous communication links
  • Connection of IP-based intercom stations
  • IP-based system interconnection via integrated Ethernet interfaces
  • LEDs to indicate operation, data transmission and errors

Linecard for 12 Digital Intercom Stations

12 DDL 02

Features and Functions

  • Management of up to 12 digital intercom stations
  • Permanent monitoring of the connected intercom stations and connection cables (interruptions, short circuits)
  • Green LED to indicate operation, red LED to indicate failures
  • One green LED per each intercom station to indicate incoming and outgoing AF signals
  • One red LED per each intercom station to indicate specific intercom station failures ¬†

Linecard for 12 Analog Intercom Stations

12 DAL 03

Features and Functions

  • Management of up to 12 analog intercom stations
  • Management of 48 line inputs / outputs
  • Protected line outputs against short circuits and overvoltage
  • Blinking LED indicates an outgoing AF signal
  • Shining LED indicates an AF source
  • Red LED indicates failures
  • Hot swapping of the linecard¬†

IP Interface for Analog Systems

NSG 001

Features and Functions

  • Interface to analog systems, with galvanic isolation
  • 3 potential-free inputs and outputs
  • Expandable to up to 27 potential-free inputs and outputs
  • Alternative wiring: bidirectional inputs/outputs
  • 4-wire AF interface with adjustable AF level
  • Continuous monitoring of network interface
  • PoE and/or external power supply
  • Integrated web interface for setting and service functions